Terex Genie GS-2669 BE Скачать руководство пользователя страница 119

Страница: 119 / 205

May 2015

Service Manual

Steer Axle Components

Part No. 1257106

GS-2669 BE • GS-3369 BE • GS-4069 BE

103

9-4

Oscillate Cylinder

How to Remove the Oscillate

Cylinder

Note: When removing a hose assembly or fitting,

the O-ring (if equipped) on the fitting and/or hose

end must be replaced. All connections must be

torqued to specification during installation. Refer to

Specifications,

Hydraulic Hose and Fitting Torque

Specifications.

1 Tag, disconnect and plug the hydraulic hoses

from the oscillate cylinder. Cap the fittings on

the cylinder.

Bodily injury hazard. Spraying

hydraulic oil can penetrate and

burn skin. Loosen hydraulic

connections very slowly to allow

the oil pressure to dissipate

gradually. Do not allow oil to

squirt or spray.

2 Chock both sides of the wheels at the

non-steer end of the machine.

3 Center a lifting jack under the drive chassis

just behind the front axle on the side of the

machine the cylinder is being removed from.

4 Remove the pivot pin retaining fasteners.
5 Using a soft metal drift, remove the pivot pin.
Note: Adjust the lifting jack to reduce the load on

the pivot pins. Do not lift the machine off of the

ground.

6 Remove the oscillate cylinder from the

machine.

9-5

Oscillate Hoses

Test the Oscillate Axle Hose

Routing

Note: Perform this procedure if the oscillate hoses

have been removed or replaced.

1 Open the ground controls compartment and

locate the function manifold.

1 function manifold

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды