Terex Genie GS-2669 BE Скачать руководство пользователя страница 129

Страница: 129 / 205

May 2015

Service Manual

Outrigger Components

Part No. 1257106

GS-2669 BE • GS-3369 BE • GS-4069 BE

113

11-1

Outrigger Cylinder

How to Remove an Outrigger

Cylinder (if equipped)

Note: When removing a hose assembly or fitting,

the O-ring (if equipped) on the fitting and/or hose

end must be replaced. All connections must be

torqued to specification during installation. Refer to

Specifications,

Hydraulic Hose and Fitting Torque

Specifications.

1 Remove the mounting fasteners from the

inside outrigger cylinder cover. Remove the

cover.

2 Remove the outrigger hose cover.
3 Disconnect the outrigger limit switch and

cylinder valve connectors.

4 Remove the mounting fasteners from the

outside outrigger cover. Remove the cover.

5 Tag, disconnect and plug the hydraulic hoses

from the outrigger cylinder. Cap the fittings on

the cylinder.

Bodily injury hazard. Spraying

hydraulic oil can penetrate and

burn skin. Loosen hydraulic

connections very slowly to allow

the oil pressure to dissipate

gradually. Do not allow oil to

squirt or spray.

6 Attach a lifting strap from an overhead crane

to the barrel end of the outrigger cylinder for

support. Do not apply any lifting pressure.

7 Remove the outrigger mounting fasteners.

Slide the outrigger cylinder down and away

from the machine.

Crushing hazard. The outrigger

cylinder may become

unbalanced and fall if not

properly supported when

removed from the machine.

Note: If the outrigger cylinder is being replaced,

remove the foot pad assembly and install it on the

replacement cylinder.
Note: After an outrigger cylinder has been installed,

the machine must be re-calibrated. Refer to Repair

Procedure,

Outrigger Calibration

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды