Terex Genie GS-2669 BE Скачать руководство пользователя страница 138

Страница: 138 / 205

Service Manual

May 2015

Battery Charger

122

GS-2669 BE • GS-3369 BE • GS-4069 BE

Part No. 1257106

13-1

Battery Charger

The machine is equipped with 2 battery chargers.

The primary charger delivers an output voltage at

full power. The boost charger delivers an output

voltage at reduce power.
If the primary charger is replaced, no adjustments

are required unless your machine is equipped with

AGM batteries. If the boost charger is replaced, the

charger must be set correctly to properly operate.
To properly set a charger, remove the plug from the

selector curve dial located on the front of the

charger. Set the selector curve to the proper

position for the battery type and charger.

1 boost charger
2 primary charger

Positions 0 and 1: Open lead flooded batteries.
Position 2: Boost charger.
Position 3: AGM batteries.

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды