Terex Genie GS-2669 BE Скачать руководство пользователя страница 115

Страница: 115 / 205

May 2015

Service Manual

Fuel and Hydraulic Tanks

Part No. 1257106

GS-2669 BE • GS-3369 BE • GS-4069 BE

8-2

Hydraulic Tank

The primary functions of the hydraulic tank is to

cool, clean and deaerate the hydraulic fluid during

operation. It utilizes internal suction strainer for the

pump supply line.

How to Remove the Hydraulic

Tank

Component damage hazard. The

work area and surfaces where

this procedure will be performed

must be clean and free of debris

that could get into the hydraulic

system and cause severe

component damage. Dealer

service is recommended.

Note: When removing a hose assembly or fitting,

the O-ring (if equipped) on the fitting and/or hose

end must be replaced. All connections must be

torqued to specification during installation. Refer to

Specifications,

Hydraulic Hose and Fitting Torque

Specifications.

1 Remove the hydraulic tank cap.
2 Remove the drain plug from the hydraulic tank

and completely drain the tank into a container

of suitable capacity. Refer to Specifications,

Machine Specifications

Bodily injury hazard. Spraying

hydraulic oil can penetrate and

burn skin. Loosen hydraulic

connections very slowly to allow

the oil pressure to dissipate

gradually. Do not allow oil to

squirt or spray.

3 Tag and disconnect the harnesses from the

ground control box.

4 Remove the ground control box from the

machine and set aside.

5 Tag, disconnect and plug the hydraulic hoses

from the hydraulic tank. Cap the fittings on the

tank.

6 Loosen the hydraulic tank mounting strap

fastener. Pull the tank strap to the side.

Note: Do not remove the tank strap.

7 Remove the hydraulic tank from the machine.

Component damage hazard.

During installation, do not

overtighten the hydraulic tank

strap mounting fastener.

Note: Clean the hydraulic tank and inspect for

cracks or other damage before installing.

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды