Terex Genie GS-2669 BE Скачать руководство пользователя страница 42

Страница: 42 / 205

Service Manual

May 2015

Checklist B Procedures

GS-2669 BE • GS-3369 BE • GS-4069 BE

Part No. 1257106

B-1

Inspect the Batteries

Genie specifications require that this procedure be

performed every 250 hours or quarterly, whichever

comes first.
Proper battery condition is essential to good engine

and machine performance and operational safety.

Improper fluid levels or damaged cables and

connections can result in engine and component

damage and hazardous conditions.

Electrocution/burn hazard.

Contact with electrically charged

circuits could result in death or

serious injury. Remove all rings,

watches and other jewelry.

Bodily injury hazard. Batteries

contain acid. Avoid spilling or

contacting battery acid.

Neutralize battery acid spills with

baking soda and water.

1 Be sure that the battery cable connections are

free of corrosion.

Note: Adding terminal protectors and a corrosion

preventative sealant will help eliminate corrosion

on the battery terminals and cables.

2 Be sure that the battery retainers and cable

connections are tight.

3 Be sure that the battery separator wire

connections are tight (if equipped).

4 Put on protective clothing and eye wear.
5 Remove the battery vent caps and check the

specific gravity of each battery cell with a

hydrometer. Note the results.

6 Check the ambient air temperature and adjust

the specific gravity reading for each cell as

follows:

•

Add 0.004 to the reading of each cell for

every 10° / 5.5° C above 80° F / 26.7° C.

•

Subtract 0.004 from the reading of each cell

for every 10° / 5.5° C below 80° F / 26.7° C.

Result: All battery cells display an adjusted

specific gravity of 1.277 or higher. The battery

is fully charged. Proceed to step 11.

Result: One or more battery cells display a

specific gravity of 1.217 or below. Proceed to

step 8.

7 Perform an equalizing charge OR fully charge

the battery(s) and allow the battery(s) to rest at

least 6 hours.

8 Remove the battery vent caps and check the

specific gravity of each battery cell with a

hydrometer. Note the results.

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды