Terex Genie GS-2669 BE Скачать руководство пользователя страница 118

Страница: 118 / 205

Service Manual

May 2015

Steer Axle Components

102

GS-2669 BE • GS-3369 BE • GS-4069 BE

Part No. 1257106

9-2

Steer Cylinder

How to Remove the Steer

Cylinder

Note: When removing a hose assembly or fitting,

the O-ring (if equipped) on the fitting and/or hose

end must be replaced. All connections must be

torqued to specification during installation. Refer to

Specifications,

Hydraulic Hose and Fitting Torque

Specifications.

1 Tag, disconnect and plug the hydraulic hoses

from the steer cylinder. Cap the fittings on the

cylinder.

Bodily injury hazard. Spraying

hydraulic oil can penetrate and

burn skin. Loosen hydraulic

connections very slowly to allow

the oil pressure to dissipate

gradually. Do not allow oil to

squirt or spray.

2 Remove the rue ring from each cylinder clevis

pin. Remove the clevis pins.

3 Remove the steer cylinder from the machine.

9-3

Tie Rod

How to Remove the Tie Rod

1 Remove the rue ring from the clevis pin

connecting the tie rod to the right side yoke

assembly. Remove the clevis pin.

1  clevis pin
2  pivot pin
3  steer sensor assembly
4  tie rod
5  rue ring

2 Remove the retaining fasteners from the pivot

pin connecting the tie rod to the left side yoke

assembly.

3 Use a small pry bar to move the pivot pin down

enough to clear the steer sensor assembly.

4 Remove the steer sensor actuator and spring

from the tie rod pivot pin and set aside.

5 Remove the steer sensor assembly and set it

aside.

6 Using a soft metal drift pin and a mallet, drive

the pivot pin up to remove it.

7 Remove the tie rod.

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды