Terex Genie GS-2669 BE Скачать руководство пользователя страница 110

Страница: 110 / 205

Service Manual

May 2015

Manifolds

GS-2669 BE • GS-3369 BE • GS-4069 BE

Part No. 1257106

2 Using a suitable lifting device, place and

secure the maximum rated load in the center

of the platform deck.

GS-2669

1500 lbs / 680 kg

GS-3369

1000 lbs / 454 kg

GS-4069

800 lbs / 363 kg

3 Press and hold the lift function enable button

and platform up button. Allow the platform to

raise completely, then continue activating the

lift function while observing the pressure

reading on the pressure gauge. Note the

pressure. Refer to Specifications,

Hydraulic

Component Specifications

4 Hold the lift relief valve with a wrench and

remove the cap.

5 Adjust the internal hex socket. Turn it

clockwise to increase the pressure or

counterclockwise to decrease the pressure.

Install the relief valve cap.

Tip-over hazard. Failure to adjust

the relief valves to specification

could result in the machine

tipping over, causing death or

serious injury. Do not adjust the

relief valve pressures higher

than specifications.

6 Repeat this procedure beginning with step 3 to

confirm the relief valve pressure.

7 Lower the platform to the stowed position.
8 Using a suitable lifting device, remove the

weight from the platform.

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды