Terex Genie GS-2669 BE Скачать руководство пользователя страница 59

Страница: 59 / 205

May 2015

Service Manual

Checklist E Procedures

Part No. 1257106

GS-2669 BE • GS-3369 BE • GS-4069 BE

12 Install the drain plug using thread sealer on

the threads.

13 Install the suction strainer using thread sealer

on the threads.

14 Install the hydraulic tank onto the machine.
15 Secure the tank with the tank strap. Do not

over tighten.

16  Install the suction hose onto the tank.
17  Install the return hose onto the tank.
18  Fill the tank with hydraulic oil until the fluid is

within the top 2 inches / 5 cm of the sight

gauge. Do not overfill.

19 Clean up any oil that may have spilled.

Properly discard the oil.

20 Install the ground control box and fuse box.

Connect the harnesses.

21 Operate all machine functions through a full

cycle and check for leaks.

22 Check the oil level in the tank and add if

needed.

23 Install the tank cover plate and install the tank

cover plate mounting fasteners.

E-2

Grease the Steer Axle Wheel

Bearings

Genie specifications require that this procedure be

performed every 2000 hours or every two years,

whichever comes first.
Perform this procedure more often if dusty

conditions exist.
Maintaining the steer axle wheel bearings is

essential for safe machine operation and service

life. Operating the machine with loose or worn

wheel bearings may cause an unsafe operating

condition and continued use may result in

component damage. Extremely wet or dirty

conditions or regular steam cleaning and pressure

washing of the machine may require that this

procedure be performed more often.

1 Loosen the wheel lug nuts. Do not remove

them.

2 Block the non-steer wheels, then center a

lifting jack under the steer axle.

3 Raise the machine 6 inches / 15 cm and place

blocks under the drive chassis for support.

4 Remove the lug nuts. Remove the tire and

wheel assembly.

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды