Terex Genie GS-2669 BE Скачать руководство пользователя страница 114

Страница: 114 / 205

Service Manual

May 2015

Fuel and Hydraulic Tanks

GS-2669 BE • GS-3369 BE • GS-4069 BE

Part No. 1257106

8-1

Fuel Tank

How to Remove the Fuel Tank

Explosion and fire hazard.

Engine fuels are combustible.

Perform this procedure in an

open, well-ventilated area away

from heaters, sparks, flames and

lighted tobacco. Always have an

approved fire extinguisher within

easy reach.

Explosion and fire hazard. When

transferring fuel, connect a

grounding wire between the

machine and pump or container.

Explosion and fire hazard. Never

drain or store fuel in an open

container due to the possibility of

fire.

1 Remove the fuel filler cap from the tank.
2 Using an approved hand-operated pump,

drain the fuel tank into a suitable container.

Refer to Specifications,

Machine

Specifications

Note: Be sure to only use a hand operated pump

suitable for use with gasoline and/or diesel fuel.

3 Clean up any fuel that may have spilled.
4 Remove the intake grill located below the fuel

tank and set aside.

5 Disconnect the engine harness from the

cooling fan inside the engine compartment.

6 Remove the cooling fan and fan shroud and

set aside.

7 Remove the fuel tank cover above the fuel

tank.

8 Disconnect the return line from the top of the

fuel tank.

9 Disconnect and plug the supply line from the

bottom of the tank.

10 Remove the fuel tank from the machine.
Note: Clean the fuel tank and inspect for cracks or

other damage before installing.

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды