Terex Genie GS-2669 BE Скачать руководство пользователя страница 63

Страница: 63 / 205

May 2015

Service Manual

Platform Controls

Part No. 1257106

GS-2669 BE • GS-3369 BE • GS-4069 BE

Platform controls

The platform controls are used to operate the

machine from the platform.
Activating a function button sends a signal to the

Electronic Control Module (ECM). When the ECM

is in the function mode, the platform controls are

used to operate the various machine functions.
The platform controls consist of an Emergency

Stop button, electronic circuit board, proportional

control handle, drive/steer enable switch, alarm,

function buttons and LED display.
For further information or assistance, contact

Genie Product support.

1  red Emergency Stop button P2
2  platform controls circuit board U3
3  proportional control handle and drive/steer

enable switch JC9

4 alarm H1

Operati onal Indicator Codes

Operational Indicator Codes

These codes are generated by the electrical

system to indicate machine operating status.

During normal operation a code will appear in the

platform controls LED readout if a condition such

as off-level, overload cutout, chassis mode

operation or pothole guards stuck occurs.
If the platform controls LED readout displays an

operational indicator code such as LL, the fault

condition must be repaired or removed before

resuming machine operation. Push in and pull out

the red Emergency Stop button to reset the

system.

Platform Controls LED Readout

Code

Condition

Off-Level

Platform Overload (CE and Australia)

Chassis Mode Operation

No Drive (option)

F053

DCON RR Thermal Protection

F054

DCON LR Thermal Protection

F055

Traction Motor RR

F056

Traction Motor LR

Lifting Disabled (option)

Engine Start Delay

Note: A code and a description of a code can also

be viewed at the ground controls LCD display.

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды