Terex Genie GS-2669 BE Скачать руководство пользователя страница 116

Страница: 116 / 205

Service Manual

May 2015

Steer Axle Components

100

GS-2669 BE • GS-3369 BE • GS-4069 BE

Part No. 1257106

9-1

Yoke Assembly

How to Remove the Yoke

1 Chock both sides of the wheels at the

non-steer end of the machine.

2 Center a lifting jack under the drive chassis at

the steer end of the machine.

3 Loosen the wheel lug bolts. Do not remove

them.

4 Raise the machine approximately 2 inches /

5 cm. Place blocks under the chassis for

support.

Crushing hazard. The chassis

will fall if not properly supported.

5 Remove the wheel lug bolts. Remove the tire

and wheel assembly.

6 Support and secure the yoke and assembly

with a lifting device.

Left side yoke:

7 Remove the retaining fasteners from the tie

rod pivot pin.

1  upper king pin
2  tie rod pivot pin
3  lower king pin
4  steer sensor assembly
5  yoke assembly

8 Use a small pry bar to move the pivot pin down

enough to clear the steer sensor assembly.

9 Remove the steer sensor actuator and spring

from the tie rod pivot pin and set aside.

10 Remove the steer sensor assembly and set it

aside.

11 Using a soft metal drift pin and a mallet, drive

the pivot pin up to remove it.

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды