Terex Genie GS-2669 BE Скачать руководство пользователя страница 49

Страница: 49 / 205

May 2015

Service Manual

Checklist B Procedures

Part No. 1257106

GS-2669 BE • GS-3369 BE • GS-4069 BE

B-11

Check the Electrical Contactor

Genie requires that this procedure be performed

every 250 hours or quarterly, whichever comes

first.
Maintaining the electrical contactor in good

condition is essential to safe machine performance.

Failure to locate a worn or damaged contactor

could result in unsafe operating conditions and may

cause component damage.

1 Open the hydraulic compartment.
2 Open the contactor box below the ground

control box.

3 Visually inspect the contact points of the

contactor for the following items:

•

Excessive burns

•

Excessive arcs

•

Excessive pitting

Electrocution/burn hazard.

Contact with electrically

charged circuits could result in

death or serious injury. Remove

all rings, watches and other

jewelry.

Note: Replace the contactor if any damage is

found.

B-12

Perform Hydraulic Oil Analysis

Genie specifications require that this procedure be

performed every 250 hours or quarterly, whichever

comes first.
Replacement or testing of the hydraulic oil is

essential for good machine performance and

service life. Dirty oil and a clogged suction strainer

may cause the machine to perform poorly and

continued use may cause component damage.

Extremely dirty conditions may require oil changes

to be performed more often. For hydraulic oil

specifications, Refer to Specifications,

Hydraulic

Specifications

Note: Before replacing the hydraulic oil, the oil may

be tested by an oil distributor for specific levels of

contamination to verify that changing the oil is

necessary. If the hydraulic oil is not replaced at the

two year inspection, test the oil quarterly. Replace

the oil when it fails the test. Refer to Maintenance

Procedure,

Test or Replace the Hydraulic Oil

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды