Terex Genie GS-2669 BE Скачать руководство пользователя страница 37

Страница: 37 / 205

May 2015

Service Manual

Checklist A Procedures

Part No. 1257106

GS-2669 BE • GS-3369 BE • GS-4069 BE

A-1

Inspect the Manuals and Decals

Genie specifications require that this procedure be

performed every 8 hours or daily, whichever comes

first.
Maintaining the operator’s and safety manuals in

good condition is essential to safe machine

operation. Manuals are included with each

machine and should be stored in the container

provided in the platform. An illegible or missing

manual will not provide safety and operational

information necessary for a safe operating

condition.
In addition, maintaining all of the safety and

instructional decals in good condition is mandatory

for safe machine operation. Decals alert operators

and personnel to the many possible hazards

associated with using this machine. They also

provide users with operation and maintenance

information. An illegible decal will fail to alert

personnel of a procedure or hazard and could

result in unsafe operating conditions.

1 Check to make sure that the operator's and

safety manuals are present and complete in

the storage container on the platform.

2 Examine the pages of each manual to be sure

that they are legible and in good condition.

Result: The operator's manual is appropriate

for the machine and all manuals are legible

and in good condition.

Result: The operator's manual is not

appropriate for the machine or all manuals are

not in good condition or is illegible. Remove

the machine from service until the manual is

replaced.

3 Open the operator's manual to the decals

inspection section. Carefully and thoroughly

inspect all decals on the machine for legibility

and damage.

Result: The machine is equipped with all

required decals, and all decals are legible and

in good condition.

Result: The machine is not equipped with all

required decals, or one or more decals are

illegible or in poor condition. Remove the

machine from service until the decals are

replaced.

4 Always return the manuals to the storage

container after use.

Note: Contact your authorized Genie distributor or

Genie if replacement manuals or decals are

needed.

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды