Terex Genie GS-2669 BE Скачать руководство пользователя страница 112

Страница: 112 / 205

Service Manual

May 2015

Manifolds

GS-2669 BE • GS-3369 BE • GS-4069 BE

Part No. 1257106

7-4

Valve Coils

How to Test a Coil

A properly functioning coil provides an

electromagnetic force which operates the solenoid

valve. Critical to normal operation is continuity

within the coil. Zero resistance or infinite resistance

indicates the coil has failed.
Since coil resistance is sensitive to temperature,

resistance values outside specification can

produce erratic operation. When coil resistance

decreases below specification, amperage

increases. As resistance rises above specification,

voltage increases.
While valves may operate when coil resistance is

outside specification, maintaining coils within

specification will help ensure proper valve function

over a wide range of operating temperatures.

Electrocution/burn hazard.

Contact with electrically charged

circuits could result in death or

serious injury. Remove all rings,

watches and other jewelry.

Note: If the machine has been in operation, allow

the coil to cool at least 3 hours before performing

this test.

1 Tag and disconnect the wiring from the coil to

be tested.

2 Test the coil resistance using a multimeter set

to resistance (Ω). Refer to the Valve Coil

Resistance Specification table.

Result: If the resistance is not within the

adjusted specification, plus or minus 10%,

replace the coil.

Valve Coil Resistance

Specification

Note: The following coil resistance specifications

are at an ambient temperature of 68°F / 20°C. As

valve coil resistance is sensitive to changes in air

temperature, the coil resistance will typically

increase or decrease by 4% for each 18°F / 20°C

that your air temperature increases or decreases

from 68°F / 20°C.

Description

Specification

Solenoid valve, 2 position 2 way

24V DC with diode

(schematic items CA, CB, CC, CD, CE,

CF)

25Ω

Solenoid valve, 2 position 3 way

24V DC with diode

(schematic items BA, FB, FF, FO, FP,

FR, )

35Ω

Solenoid valve, 3 position 5 way

24V DC with diode (schematic item FL)

35Ω

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды