Terex Genie GS-2669 BE Скачать руководство пользователя страница 123

Страница: 123 / 205

May 2015

Service Manual

Steer Axle Components

Part No. 1257106

GS-2669 BE • GS-3369 BE • GS-4069 BE

107

17 Install the steer sensor actuator onto the tie

rod pivot pin.

18 Insert the compression spring into the steer

sensor and push the tie rod pivot pin up until

the actuator hex pin is engaged into the steer

sensor.

Note: Be sure the sensor actuator hex pin is

engaged into the sensor.

19 Rotate the tie rod pivot pin counterclockwise

approximately 90° and secure it to the tie rod.

20 Install the steer sensor cover.
21 Connect the steer sensor harness to the main

harness and secure with the cable clamp.

22 Calibrate the steer sensor. Refer to Repair

Procedure,

How to Calibrate the Steer Angle

Sensor

How to C alibr ate the Steer Angle Sensor

How to Calibrate the Steer Angle

Sensor

1 Turn the key switch to the ground controls

position and pull out the red Emergency Stop

button to the on position at the platform

controls.

2 Press and hold the ground control scroll up

and scroll down buttons.

1  scroll down button
2  enter button
3  scroll up button
4  escape button
5  LCD display

3 Pull out the red Emergency Stop button to the

on position at the ground controls.

Result: The ground controls LCD display will

show the following:

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды