background image

1

ORIGINAL INSTRUCTIONS

VES Andover Ltd Eagle Close Chandlers Ford Ind. Est Eastleigh Hampshire SO53 4NF
Tel: 08448 156060  Fax: 02380 261204  E-mail: [email protected] Web: www.ves.co.uk

Installation, Operation and Maintenance Manual

®

EVC

 Heat Recovery Unit

VES Ref. ID.1120

Issue  D

June 2016

This manual must be read in full before Installation, Operation and Maintenance of the units supplied

Please ensure that this document is passed to the end user. This manual forms an integral part of
the product and should be kept for the working life of the product. Additional copies of this and
supporting documents are available by contacting VES or by visiting 

www.ves.co.uk

 and following

the 'Download O & M's' link.

The following symbols used within this document refer to potential dangers, advice for safe
operation or important points of reference

Indicates hazards associated with electric current and high voltages

Indicates hazards that require safety advice for personnel or potential unit/property damage

Indicates important information

page

Introduction

1

Nomenclature

2

Receipt of Goods & Handling

3

Installation

3

Standard Wiring & Fan Installation

8

Maintenance

15

The Ecovent® 

EVC 

series is a range of Heat Recovery units, with duties up to 1.3 m³/s. Suitable for

either plantroom, ceiling void or internal locations. As standard, each unit will have been supplied
pre-wired to an isolator or fitted control panel, as specified at the time of order.
The standard operating temperature of these units is -20 to +35 °C.

For further technical details regarding dimensions and weights, contact VES on 

08448 15 60 60

,

quoting the sales order (SO) number and the unit type as found on the unit nameplate, or
alternatively visit 

www.ves.co.uk

.

Warning

Caution

Important

Important

Introduction

1
2
3
4
5
6

1

Contents

Содержание ecovent EVC




















Отзывы: