background image

4

ORIGINAL INSTRUCTIONS

VES Andover Ltd Eagle Close Chandlers Ford Ind. Est Eastleigh Hampshire SO53 4NF
Tel: 08448 156060  Fax: 02380 261204  E-mail: [email protected] Web: www.ves.co.uk

Installation, Operation and Maintenance Manual

®

EVC

 Heat Recovery Unit

Continued

Ecovent® 

EVC

 units are supplied with feet suitable for floor or ceiling-void mounting, either by

use of drop-rod mounting, in either top or bottom access orientation, with airflow in the
horizontal plane. For alternative mounting please consult your outline drawing as supplied with
the unit, or refer to VES Customer Services for further information.

Secure drop rods/unit with the appropriate fixings as shown below       .
Self-levelling feet are available for floor mounting, with fixings as per drop rods       . The unit can
be further secured to the floor via knockout fixings holes on the feet, fixings to be supplied by
others        .

When hanging units from drop-rods, ensure that the load is evenly spread and that 

ALL 

feet are

used within the support, including those for fitted silencers if included.
Ensure that the drop rod used is selected appropriatedly to accomodate the load of the unit.

Unit mounting detail

Fig.

3 4 5

Installation

4

Important

EVC

 units with fitted silencers are sectional and handed. It is important that all sections are

joined together securely prior to positioning and installation. Remove and retain the fixings
from the joining bracket. Butt the correct silencer to the unit section ensuring the unit spigots
enter the silencer section fully see fig.

6

. This joint should be assembled using self-adhesive

rubber tape at the joints prior to assembly so as to prevent air leakage; replace with similar if
damaged. Finish the assembly by installing the joint fixings through both parts of each joining
bracket and tighten using a 6mm hex key, drawing the sections together evenly see fig.

7

.

Section joining detail

Fig.

6 7

Caution

Joining brackets are 

NOT 

structural and are included as part of the unit sealing only.

When moving assembled units ensure that 

ALL 

sections are fully supported.

7

6

3

4

5

3

4

5

Содержание ecovent EVC




















Отзывы: