Terex Genie GS-2669 BE Скачать руководство пользователя страница 126

Страница: 126 / 205

Service Manual

May 2015

Non-steer Axle Components

110

GS-2669 BE • GS-3369 BE • GS-4069 BE

Part No. 1257106

10-1

Drive Motors

How to Remove a Drive Motor

The drive motors are AC powered and are a

brushless design requiring very little maintenance.

They have built-in speed and temperature sensors

which is monitored by the ground controls (GCON).

The speed sensor is a Hall-effect type and is part of

the rear motor shaft bearing. The temperature

switch will shut down the drive motor if it becomes

excessively hot.

1 Disconnect the battery pack from the machine.

Electrocution/burn hazard.

Contact with electrically charged

circuits could result in death or

serious injury. Remove all rings,

watches and other jewelry.

2 Chock both sides of the wheels at the steer

end of the machine.

3 Center a lifting jack under the drive chassis at

the non-steer end of the machine.

4 Loosen the wheel lug nuts. Do not remove

them.

5 Raise the machine approximately 2 inches /

5 cm. Place blocks under the chassis for

support.

Crushing hazard. The chassis

will fall if not properly supported.

6 Remove the wheel lug bolts. Remove the tire

and wheel assembly.

7 Remove the axle cover.

1  axle cover
2  drive hub
3  axle assembly

8 Tag and disconnect the electrical connectors

for the brake, speed and temperature sensors

at the drive motor.

9 Tag and disconnect the electrical connectors

for the oscillate limit switches.

10 Tag and disconnect the drive motor power

cables from the motor controller in the ground

controls compartment.

Note: The power cables will have to be pulled

through the drive chassis when the axle assembly

is removed.

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды