Terex Genie GS-2669 BE Скачать руководство пользователя страница 121

Страница: 121 / 205

May 2015

Service Manual

Steer Axle Components

Part No. 1257106

GS-2669 BE • GS-3369 BE • GS-4069 BE

105

9-6

Steer Angle Sensor

How to Replace the Steer Angle

Sensor

The steer angle sensor, installed on the steer yoke,

is monitored by the control system to determine

steer angle. The control system uses the steer

angle input, along with pre-programmed

parameters, to vary the speed of each drive motor

while steering to minimize tire scrub and to help

minimize turning radius. Drive speed is also

reduced proportionately depending on the steer

angle to minimize lateral platform acceleration.

1 Adjust the steer tires so they are in a straight

driving position.

2 Turn the key switch to the off position.
3 Push in the red Emergency Stop button to the

off position at both the ground and platform

controls and turn the key switch to the off

position.

4 Remove the cable clamp securing the steer

sensor cable to the chassis.

5 Tag and disconnect the steer sensor harness

from the main harness.

6 Remove the steer sensor cover.

7 Remove the tie rod pivot pin retaining

fasteners.

1  left yoke assembly
2  steer sensor cover
3  compression spring
4  steer sensor actuator
5  tie rod pivot pin

8 Use a small pry bar to move the pivot pin down

enough to clear the steer sensor assembly.

9 Remove the steer sensor actuator and spring

from the tie rod pivot pin and set aside.

Note: Inspect the steer sensor actuator to make

sure it is not broken or twisted.

Содержание Genie GS-2669 BE














































































































































































































Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды

Terex Genie GS-2669 BE, Руководство по обслуживанию

Результаты поиска

Содержание Genie GS-2669 BE

Отзывы:

Похожие инструкции для Genie GS-2669 BE

Бренды по названию

Популярные бренды