Sony MVS-8000X SystemMVS-7000X System, Руководство пользователя

Страница: 186 / 706

USO
RESTRITO
186
Overview
Ch
a
p
te
r 6
DM
E
W
ip
e
s
• 1031
When this pattern number is selected, with the
progress of the transition the pattern center
automatically moves initially from the set position
toward the center of the screen
(see page 189) . In
other words, the effect obtained is the same as in a
normal wipe with the positioner set to [Auto Center].
• 1201 to 1208, 1221 to 1224, 1251
When these pattern numbers are selected, you can
set the pattern position when the first transition
completes.
• 1381, 1391, 1393, 1394, 1396
When these pattern numbers are selected, you can
set the center of the transition effect.
• 2651, 2652
When these pattern numbers are selected, you can
move the pattern for each channel, or with values
relative to the current position the two channels
simultaneously.
• 2801 to 2804, 2811 to 2814
When these pattern numbers are selected, you can
set the vertical position as the brick slides in.
• 2851 to 2854, 2861 to 2864
When these pattern numbers are selected, you can
set the pattern position for each channel setting when
the first transition completes.
Pattern limit: You can restrict the range of the transition
as desired. However, this is not available for a DME
wipe in the independent key transition control block.
For more details, see “Pattern Limit” (page 107).
Size: You can set the size of the image. This can only be
used when one of the following pattern numbers is
selected.
• 1201 to 1208, 1221 to 1224, 1251
• 2651, 2652, 2851 to 2854, 2861 to 2864
Crop: You can crop the image. It is also possible in 16:9
mode to crop both sides to convert the image to a 4:3
aspect ratio. For the execution of a DME wipe crop
transition, you can select from the following three
possibilities.
•
Cut
•
Last 5%
•
Linear
When [Last 5%] is selected, you can set the [Release
Transition] as follows.
•
Last 30%
•
Last 5%
•
Off
Notes
When pattern numbers 1701 and 1702 are selected,
crop cannot be used.
Relation Between DME Wipes and
Other Effects
The relations between DME wipes and other effects are as
follows.
Relation to ordinary wipes
•
DME wipes do not use the wipe generator built into the
switcher. Therefore, during the execution of a DME
wipe, you can still use a pattern produced by the wipe
generator as the source for a pattern key or mask.
•
A DME wipe pattern cannot be used as the source for a
pattern key or mask.
Relation to processed keys
When using the DME for a processed key, if you select a
DME wipe, an available DME is automatically allocated to
the DME wipe. If all of the DME channels are in use, then
it is not possible to select a DME wipe.
If in a Setup menu a setting has been made for DME
allocation, that Setup menu setting takes precedence.
For details, see “Setting the assignments of DME channels
to use on the individual M/E banks” in Chapter 20
(Volume 2).
Relation to resizer
When resizer is enabled, it is not possible to select a DME
wipe.
For the key 1 and key 2, key 3 and key 4, key 5 and key 6,
or key 7 and key 8 combinations, if one is used for a dual
resizer effect, the other key cannot be used for a DME
wipe.
Number of DME wipes that can be used
simultaneously on a single M/E bank
DME wipes can be used in nine places, including the eight
independent key transitions.
Notes
•
When the signal format is 1080P, DME wipes can be
used in five places, including the four independent key
transitions.
•
When the SDI interface is used to connect the DME,
DME effects (including DME wipes) can be used in only
one place for one M/E bank.
•
When the dedicated interface is used to connect the
DME, the number of keys to which DME effects
(including DME wipes) can be applied simultaneously
for one M/E bank varies as follows depending on the
execution mode of the DME wipe pattern selected for the
background.