Sony MVS-8000X SystemMVS-7000X System, Руководство пользователя

Страница: 521 / 706

USO
RESTRITO
Macro Attachment Assigning
521
Ch
a
p
te
r 16
M
a
c
ro
s
Executing a Macro by Macro
Attachment
Notes
For execution on any of the M/E and PGM/PST banks, use
the [MCRO ATTCH ENBL] button in the cross-point
control block. To execute a macro according to a macro
attachment set elsewhere, assign “MCRO ATTCH ENBL”
to a utility/shotbox control block or user preference button,
then use that button.
Executing a macro assigned to a button
1
Depending on the location of the button you want to
To disable macro attachment settings
Depending on the location of the button you want to
disable, press the [MCRO ATTCH ENBL] button, turning
it off.
In this state, pressing a button for which a macro
attachment is set does not execute the macro.
Executing a macro assigned to a fader
lever
1
In the cross-point control block for the fader lever on
which you want to execute the macro, press the
[MCRO ATTCH ENBL] button, turning it on.
2
use, press the [MCRO ATTCH ENBL] button, turning
it on.
2
Press the desired button for which a macro attachment
has been set.
This recalls the macro register assigned to the button,
and the macro is executed as follows, according to the
operation mode.
Pre macro mode: The macro is executed first, and
then the button function is executed.
Post macro mode: The button function is executed
first, and then the macro is executed.
Macro only mode: The button function is not
executed, and the macro only is executed.
During macro execution, the button you pressed
flashes.
Notes
•
It is not possible to execute more than one macro at a
time. Therefore, even if you simultaneously press
multiple buttons for which macro attachments are set,
only one macro is executed.
•
If a button is pressed twice during macro execution or
when the macro is stopped, or if another macro is
recalled, the following operation (stop or continue)
depends on a setting in setup.
For details of the settings, see “Setting the Macro
Execution Mode” (page 606).
•
Individual events stored in a macro are executed
according to the settings in setup. If you change the
settings in setup, a saved macro may not have the
expected effect.
•
During macro execution, if you switch the control panel
to macro editing mode, the macro being executed stops.
•
During macro editing, pressing a button for which a
macro attachment is set does not execute the macro.
Move the fader lever from the start position to the end
position.
When the fader lever passes the position at which the
macro attachment is set, the macro register is recalled,
and the macro is executed.
Notes
•
Unless you move the fader lever to the end position
(completing the travel), it is not possible to execute the
macro again.
•
When the preset color mix stroke mode is Normal, the
first lever operation executes the macro, but the second
lever operation does not.
For details, see “Setting a preset color mix” (page 623).
•
If a button is pressed twice during macro execution or
when the macro is stopped, or if another macro is
recalled, the following operation (stop or continue)
depends on a setting in setup
(see page 606) .
•
Individual events stored in a macro are executed
according to the settings in setup. If you change the
settings in setup, a saved macro may not have the
expected effect.
•
During macro execution, if you switch the control panel
to macro editing mode, the macro being executed stops.
•
During macro editing, even if you operate a fader lever
with a macro attachment set, the macro is not executed.
To disable a macro attachment setting
In the cross-point control block for the fader lever on
which you want to disable the macro, press the [MCRO
ATTCH ENBL] button, turning it off.
In this state, operating a fader lever with a macro
attachment set does not execute the macro.