10-14
Serial Port Communications and Commands
Date Code 990215
SEL-351P Manual Técnico
The definitions are:
RECLOSER R1: This is the Recloser ID, RID, setting (the control is shipped with the
default setting RID = RECLOSER R1; see
Identifier Labels
in
Section 9:
Setting the SEL-351P Recloser Control
).
FEEDER 2101: This is the Terminal ID, TID, setting (the control is shipped with the
default setting TID = FEEDER 2101; see
Identifier Labels
in
Section 9:
Setting the SEL-351P Recloser Control
).
Date:
This is the date the command response was given [except for recloser
control response to the EVE command (Event), where it is the date the
event occurred]. You can modify the date display format
(Month/Day/Year or Year/Month/Day) by changing the DATE_F recloser
control setting with the SET G command.
Time:
This is the time the command response was given (except for control
response to the EVE command, where it is the time the event occurred).
The serial port command explanations that follow in the
Command Explanations
subsection are
in the same order as the commands listed in Table SECTION 10: .5.
C
OMMAND
E
XPLANATIONS
Access Level 0 Commands
ACC, EZA, BAC, and 2AC Commands (go to Access Level 1, E, B, or 2)
The ACC, EZA, BAC, and 2AC commands provide entry to the multiple access levels. Different
commands are available at the different access levels as shown in Table SECTION 10: .5.
Commands ACC, EZA, BAC, and 2AC are explained together because they operate similarly.
•
ACC moves from Access Level 0, E, 2, or B to Access Level 1.
•
EZA moves from Access Level 0, 1, 2, or B to Access Level E (EZ).
•
BAC moves from Access Level 1, 2 or E to Access Level B.
•
2AC moves from Access Level 1, E or B to Access Level 2.
Password Requirements and Default Passwords
Passwords are required if the main board Password jumper is not in place (Password jumper =
OFF). Passwords are not required if the main board Password jumper is in place (Password
jumper = ON). Refer to Table 2.4 and Table 2.5 for Password jumper information. See PAS
Command explanation later in this section for more information on passwords.
The factory default passwords for Access Levels 1, E, B, and 2 are:
Access Level
Factory Default Password
1
OTTER
E
DAKOTA
Содержание SEL-351P
