manualshive.com logo in svg

Samsung S3C6400X, Руководство пользователя, Страница: 573 / 1189

Поделиться
Скачать
Samsung S3C6400X Скачать руководство пользователя страница 573

 

PRELIMINARY 

CAMERA INTERFACE

 

 

S3C6400X RISC MICROPROCESSOR 

20-8                                                                                                                                                         

 

Preliminary product information describe products that are in development,

 

for which full characterization data and associated errata are not yet available.

Specifications and information herein are subject to change without notice.

 

CLOCK DOMAIN 

Camera Interface has two clock domains. The one is the system bus clock, which is HCLK. The other is the pixel 

clock, which is PCLK. 

The system clock must be faster than pixel clock

. As highlighted in figure 20- 7, CAMCLK 

must be divided from the fixed frequency like APLL or MPLL clock. If external clock oscillator is used, CAMCLK 

must be floated. Internal scaler clock is system clock. It is not mandatory for two clock domains to be 

synchronized with each other. Other signals as PCLK must be similarly connected to shimitt-triggered level shifter. 

 

XciCLK

Divide 

Counter

1/1,1/2,1/3...~

1/16

APLL or 

MPLL

External

Camera

Processor

XciPCLK

CAMIF

(f

mpll

 or f

apll 

)/d

f

mpll

 or 

f

apll

MPLL

Variable

Freq.

Divide 

Counter

f

mpll 

/d

f

mpll 

HCLK

External MCLK

Normally use

Schmit-triggered 

Level-shifter

 

Figure 20-7. CAMERA INTERFACE clock generation 

 

 

 

 

 

 

 

 

Содержание S3C6400X






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов