manualshive.com logo in svg

Samsung S3C6400X, Руководство пользователя, Страница: 54 / 1189

Поделиться
Скачать
Samsung S3C6400X Скачать руководство пользователя страница 54

 

PRELIMINARY 

S3C6400X RISC MICROPROCESSOR

 

 

                                           SYSTEM CONTROLLER 

 

3-9 

Preliminary product information describe products that are in development,

 

for which full characterization data and associated errata are not yet available.
Specifications and information herein are subject to change without notice.

Camera I/F clock generation 

Figure 3-9 shows the clock generator for the camera interface. All data for camera interface is 
transferred/received based on this clock. The maximum operating clock is up to 133MHz. 

 

Figure 3-9. Camera I/F clock generation 

 

Clock generation for display (POST, LCD, and scaler) 

Figure 3-10 shows the clock generator for display blocks. Usually LCD controller requires image post-processor 
and scaler logic. The operating clocks can be independently controlled with this clock generator. CLKLCD and 
CLKPOST are connected to LCD controller and post-processor, respectively, within domain-F. CLKSCALER is 
connected to scaler block within domain-P. 

EPLL

1

0

MUX

EPLL

MUX

SCALER

MPLL

1

0

DIV

MPLL

1

0

EXTCLK

XTIpll

MUX

MPLL

CLKSCLAER

DIV

SCALER

SCLK_GATE[16]

CLK_DIV1[19:16]

CLKLCD

DIV

LCD

SCLK_GATE[14]

CLK_DIV0[15:12]

2

0

1

2

0

1

CLK_SRC[1]

CLK_SRC[2]

CLK_DIV0[4]

CLK_SRC[27:26]

CLK_SRC[29:28]

MUX

LCD

SCLK_GATE[10]

CLKPOST

 

Figure 3-10. Display clock generation 

Содержание S3C6400X






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов