manualshive.com logo in svg

Samsung S3C6400X, Руководство пользователя, Страница: 1051 / 1189

Поделиться
Скачать
Samsung S3C6400X Скачать руководство пользователя страница 1051

 

PRELIMINARY 

Real Time Clock

  

S3C6400 

RISC MICROPROCESSOR

 

 

33-6 

Preliminary product information describe products that are in development,

 

for which full characterization data and associated errata are not yet available.
Specifications and information herein are subject to change without notice.

 

INDIVIDUAL REGISTER DESCRIPTIONS 

REAL TIME CLOCK CONTROL (RTCCON) REGISTER  

The RTCCON register consists of 9 bits such as the RTCEN.  It controls the read/write enable of the BCD SEL, 
CNTSEL and CLKRST for testing. 
RTCEN bit can control all interfaces between the CPU and the RTC, Therefore it must be set to 1 in an RTC 
control routine to enable data read/write after a system reset. Before power off, the RTCEN bit must be cleared 
to 0 to prevent inadvertent writing into RTC registers. 
 

Register 

Address 

R/W 

Description 

Reset Value 

RTCCON 0x7E005040 

R/W 

RTC control Register 

0x0 

 
 
 

RTCCON 

Bit 

Description 

Initial State 

TICEN 

[8] 

Tick timer enable 
0 = Disable                 1 = Enable 

0 

Reserved [7:4]  Reserved 

 

CLKRST 

[3] 

RTC clock count reset. 
0 = No reset,     1 = Reset 

0 

CNTSEL [2] 

BCD 

count 

select. 

0 = Merge BCD counters 
1 = Reserved (Separate BCD counters) 

0 

CLKSEL 

[1] 

BCD clock select. 
0 = XTAL 1/2

15

 divided clock     

1 = Reserved (XTAL clock only for test) 

0 

RTCEN [0]  RTC 

control 

enable. 

0 = Disable               1 = Enable 
Note: When RTCEN is enable, BCD time count setting, RTC clock 
counter reset and read operation can be performed. 

0 

 

 

 

 

Note: 
 

TIC Counter is enabled / disabled at TICCLK rising edge.  
If TICEN is high, TIC counter is updated at TICCLK rising edge 
But, if TICEN is low, TIC counter is cleared at TICCLK rising edge.  
  
 
 

TICK TIME COUNT  REGISTER (TICNT) 

Register 

Address 

R/W 

Description 

Reset Value 

TICNT 0x57000044 

 

R/W 
 

Tick time count  register  

0x0 

 
 

TICNT 

Bit 

Description 

Initial State 

TICK TIME 
COUNT  

[15:0] 

16 bit tick time count value  

16’b0 

Содержание S3C6400X






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов