![background image](http://html1.mh-extra.com/html/magnetek/hpv-900-series-2/hpv-900-series-2_technical-manual_3606659071.webp)
Drive A1 Submenu
49
Parameter
[
Alphanumeric]
Description
Units
Range
Default
Hidden
Item
Run
lockout
ENGLISH
(U3)
METRIC
(U3)
Spd
Command
Mult
[A154]
(Speed Command Multiplier) This parameter
scales the analog speed command.
uses
software
drive
signal
MULT
COMMAND
SPD
BIAS
COMMAND
SPD
voltage
input
channel#1
analog
none
-10.00 -
+10.00
1.00
Y
Y
Spd Zero
Band
[A155]
(Speed Zero Band) Voltage range that is
considered to be a zero speed command
when analog speed commands are used.
Typical value less than 50 mV. Can be
determined by shorting to/- analog
speed command inputs and view results in
ANALOG SPD CMD (D1).
volts
0.000
– 1.000
0.000
N
Y
Pre Torque
Bias
i
,ii
[A156]
(Pre-Torque Bias
i
,ii
) This parameter
subtracts an effective voltage to the actual
analog pre torque command (channel 2)
voltage signal.
uses
software
drive
signal
MULT
TORQUE
PRE
BIAS
TORQUE
PRE
voltage
input
channel#2
analog
volts
i
,ii
-6.00
– 6.00
i
,ii
0.00
i
,ii
Y
i
,ii
Y
i
,ii
Pre Torque
Mult
i
,ii
[A157]
(Pre-Torque Multiplier
i
,ii
) This parameter
scales the analog pretorque command
(channel 2).
uses
software
drive
signal
MULT
TORQUE
PRE
BIAS
TORQUE
PRE
voltage
input
channel#2
analog
none
i
,ii
-10.00 -
+10.00
i
,ii
1.00
i
,ii
N
i
,ii
Y
i
,ii
Pre Torque
Time
i,ii
[A158]
(Pre Torque Time
i,ii
)
Time to ramp torque
from zero to pre-torque value. When set to
zero, Pre-Torque will be applied
immediately. This helps eliminate the
‘bump’ felt upon starting caused by the
torque being immediately set to rated pre-
torque. Setting this parameter to zero will
disable the Pre Torque Ramp Up function.
With a non-zero setting for Pre Torque Time,
the torque reference will be linearly ramped
from zero to the value given through the
Analog Input Channel or the serial channel.
sec
i,ii
0.00
– 10.00
i,ii
0.00
i,ii
N
i,ii
N
i,ii
Ext Torque
Bias
i
,ii
[A159]
(External Torque Bias
i
,ii
) This parameter
subtracts an effective voltage to the actual
analog pre torque / torque command
(channel 2) voltage signal. For more
information, see Analog Inputs on page 32.
uses
software
drive
signal
MULT
TORQUE
EXT
BIAS
TORQUE
EXT
voltage
input
channel#2
analog
volts
i,ii
-6.00
– 6.00
i,ii
0.00
i,ii
N
i
,ii
N
i
,ii
Ext Torque
Mult
i,ii
[A160]
(External Torque Multiplier
i
,ii
)
This
parameter scales the analog pretorque /
torque command (channel 2). If this function
is set to 1.00, a 10V signal will call for 100%
torque. For more information, see Analog
Inputs on page 32.
uses
software
drive
signal
MULT
TORQUE
EXT
BIAS
TORQUE
EXT
voltage
input
channel#2
analog
none
i,ii
-10.00 -
+10.00
i,ii
1.00
i,ii
N
i
,ii
N
i
,ii
i
Parameter accessible through
CLOSED LOOP (U9)
Operation
ii
Parameter accessibly through
PM (U9)
Operation
iii
Parameter accessible through
OPEN LOOP(U9)
Operation
Содержание HPV 900 Series 2
