![background image](http://html1.mh-extra.com/html/magnetek/hpv-900-series-2/hpv-900-series-2_technical-manual_3606659113.webp)
User Switches C1 Submenu
91
Parameter
[Alphanumeric]
Description
Choices
Default
Hidden
item
Run
lockout
ENGLISH
(U3)
METRIC
(U3)
Endat Out
Mult
[C145]
This parameter is the encoder PPR
multiplier that sets the pulse rate of the
differential quadrature buffered output on
the EnDat board
8
1
2
4
8
N
Drv Enable
Src
[C146]
(Drive Enable Source)
This parameter allows the user to choose
the source of the drive enable command
from one of the following sources: an
external run signal from a logic input
(external TB1), a drive enable signal
transferred across a serial channel
(serial), or a signal from both the serial
channel and a logic input (extrn). If
a signal is required from a logic input
(either externaltb1 or extrn), the
drive enable signal on TB1 must be
selected.
external tb
[1]
serial
[2]
extrn
[3]
EXTERNAL TB
N
Y
Rec Travel
Dir
[C147]
(Recommended Travel Direction)
This parameter allows the user to enable
and select the appropriate installation type
to allow the drive to travel in the lightest
load direction (generally for use with a
UPS to allow the rescue of trapped
passengers when mains power is not
available). This function can be enabled
by assertion of any logic input (C2)
configured to ‘REC TRAVEL EN’
none
[0]
geared
[1]
gearless
[2]
NONE
N
N
Phase Loss
Check
[C148]
(Phase Loss Check Selection)This
parameter allows the user to select the
sensitivity of the phase loss detection.
Low sens setting phase loss condition
must be twice as low as at high sens
setting for a phase flt to be declared. If
disabled a phase fault will not be
declared.
high sens
[1]
low sens
[2]
disabled
[0]
HIGH SENS
N
Y
Overload
Select
[C149]
(Overload Select) This parameter allows
the user to select the over load capacity of
the drive, 200% for normal duty or 250%
for heavy duty.
NOTE:
NOT available on
drive models: 2075, 2088, 2098, 4065,
4072, and 4096.
When selecting 200%, set PWM
Frequency (A4) to 8kHz.
200%
[200%]
250%
[250%]
250%
N
Y
NTSD Mode
[C150]
(Normal Terminal Stopping Device Mode)
Sets the number of threshold checkpoints
in the hoistway and threshold speeds for
the NTSD function. If set to external, the
speed threshold is determined by the
controller or if NTSD is not used.
1 Threshold
[1]
2 Thresholds
[2]
3 Thresholds
[3]
External
[4]
External
N
N
Balance
Comp
[C151]
(Balance Compensation) Minimizes
fundamental harmonics in the current
feedback circuit. Enabling this function
can help improve the ride quality,
especially for a PM motor.
Enable
[1]
Disable
[0]
Disable
N
Y
Содержание HPV 900 Series 2
