![background image](http://html1.mh-extra.com/html/magnetek/hpv-900-series-2/hpv-900-series-2_technical-manual_3606659171.webp)
Troubleshooting
149
Name
Description
Possible Causes & Corrective Action
Undervolt Flt
[F47]
This fault is generated during a run
condition if the DC bus voltage falls
below the level that is specified by UV
Fault Level (A4).
Fault is declared when:
)
4
(
*
2
*
)
4
(
A
Volts
L
L
Input
A
Level
Fault
UV
volt
bus
DC
Low Input Voltage
Check INPUT L-L VOLTS (A4) and UV
FAULT LEVEL (A4) parameters
Disconnect Dynamic Braking resistor
and re-try.
Verify proper input voltage and increase,
if necessary, the input AC voltage within
the proper range
Check for a missing input phase
Check power line disturbances due to
starting of other equipment
Drive Accurately Reading the Dc Bus
Measure the dc bus with a meter across
terminals B1 and
–
Compare that with the value on the
digital operator, DC BUS VOLTAGE
(D2)
Hardware Problem
The drive may need to be replaced.
Uv Alarm
(alarm)
[F73]
This alarm is generated during a run
condition if the DC bus voltage falls
below the level that is specified by UV
Alarm Level (A4).
Alarm is declared when:
)
4
(
*
2
*
)
4
(
A
Volts
L
L
Input
A
Level
Alarm
UV
volt
bus
DC
Low Input Voltage
Check INPUT L-L VOLTS (A4) and UV
ALARM LEVEL (A4) parameters
Disconnect Dynamic Braking resistor
and re-try.
Verify proper input voltage and increase,
if necessary, the input AC voltage within
the proper range
Check for a missing input phase
Check power line disturbances due to
starting of other equipment
Drive Accurately Reading the Dc Bus
Measure the dc bus with a meter across
terminals B1 and
–
Compare that with the value on the
digital operator, DC BUS VOLTAGE
(D2)
Hardware Problem
The drive may need to be replaced.
V/Hz Fault
(open loop)
[F55]
This fault is following two formulas are
not satisfied:
VOLTS
MTR
RATED
VOLTS
MID
MOTOR
VOLTS
MIN
MOTOR
:
FREQ
EXCIT
RATED
FREQ
MID
MOTOR
FREQ
MIN
MOTOR
Check Parameters Settings:
Check RATED MTR VOLTS (A5)
parameter for correct setting
Check MOTOR MID VOLTS (A5)
parameter for correct setting
Check MOTOR MIN VOLTS (A5)
parameter for correct setting
Check RATED EXCIT FREQ (A5)
parameter for correct setting
Check MOTOR MID FREQ (A5)
parameter for correct setting
Check MOTOR MIN FREQ (A5)
parameter for correct setting
Содержание HPV 900 Series 2
