INVT Goodrive20-EU VFD Series Скачать руководство пользователя страница 7

Страница: 7 / 173

Goodrive20-EU Series VFD

Safety precautions

-2-

Symbols

Name

Instruction

Abbreviation

Hot sides

Sides of the device may become

hot. Do not touch.

Note

Physical hurt may occur if not

follow the relative requirements

Note

1.3 Safety guide



Only qualified electricians are allowed to operate on the VFD.



Do not carry out any wiring, inspection or component replacement when

the power supply is applied. Ensure all input power supply is disconnected

before wiring and checking and always wait for at least the time designated

on the VFD or until the DC bus voltage is less than 36V. The table below

describes the waiting time:

VFD model

Minimum waiting time

1PH 230V

0.4kW

–2.2kW

5 minutes

3PH 230V

0.4kW

–7.5kW

5 minutes

3PH 400V

0.75kW

–110kW

5 minutes



Do not refit the VFD unless authorized; otherwise, fire, electric shock or

other injury may occur.



The base of the radiator may become hot during running. Do not touch to

avoid hurt.



The electrical parts and components inside the VFD are electrostatic. Take

measurements to avoid electrostatic discharge during related operation.

1.3.1 Delivery and installation



Please install the VFD on fire-retardant material and keep the VFD away

from combustible materials.



Connect the optional brake parts (braking resistors, braking units or

feedback units) according to the wiring diagram.



Do not operate on the VFD if there is any damage or components loss to

the VFD.



Do not touch the VFD with wet items or body; otherwise, electric shock

may occur.

Note:



Select appropriate moving and installing tools to ensure a safe and normal running of the

VFD and avoid physical injury or death. For physical safety, the erector should take some

mechanical protective measurements, such as wearing exposure shoes and working
uniforms.

Содержание Goodrive20-EU VFD Series














































































































































































Результаты поиска

Содержание Goodrive20-EU VFD Series

Отзывы:

Похожие инструкции для Goodrive20-EU VFD Series

Бренды по названию

Популярные бренды

INVT Goodrive20-EU VFD Series, Руководство по эксплуатации

Результаты поиска

Содержание Goodrive20-EU VFD Series

Отзывы:

Похожие инструкции для Goodrive20-EU VFD Series

Бренды по названию

Популярные бренды