INVT Goodrive20-EU VFD Series Скачать руководство пользователя страница 73

Страница: 73 / 173

Goodrive20-EU Series VFD

Function parameters

-68-

Function

code

Name

Description

Default Modify

AO2 output to

the lower limit

10V (20mA)

0.0%

100.0%

Setting range of P06.17: -100.0%

– P06.19

Setting range of P06.18: 0.00V

–10.00V

Setting range of P06.19: P06.17

–100.0%

Setting range of P06.20: 0.00V

–10.00V

Setting range of P06.21: 0.000s

–10.000s

Setting range of P06.22:- 100.0%

– P06.24

Setting range of P06.23: 0.00V

–10.00V

Setting range of P06.24: P06.22

–100.0%

Setting range of P06.25: 0.00V

–10.00V

Setting range of P06.26: 0.000s

–10.000s

P06.24

Upper limit of

AO2 output

100.0%

○

P06.25

Corresponding

AO2 output to

the upper limit

10.00V

○

P06.26

AO2 output

filter time

0.000s

○

P07 group HMI

Function

code

Name

Description

Default Modify

P07.00 User password

–65535

The password protection will be valid when

setting any non-zero number.

00000: Clear the previous user's password, and

make the password protection invalid.

After the user's password becomes valid, if the

password is incorrect, users cannot enter the

parameter menu. Only correct password can

make the user check or modify the parameters.

Please remember all users' passwords.

Retreat editing state of the function codes and

the password protection will become valid in 1

minute. If the password is available, press

PRG/ESC to enter into the editing state of the

function codes, and then "0.0.0.0.0" will be

displayed. Unless input right password, the

operator cannot enter into it.

Note:

Restoring to the default value can clear

the password, please use it with caution.

○

Содержание Goodrive20-EU VFD Series














































































































































































Результаты поиска

Содержание Goodrive20-EU VFD Series

Отзывы:

Похожие инструкции для Goodrive20-EU VFD Series

Бренды по названию

Популярные бренды

INVT Goodrive20-EU VFD Series, Руководство по эксплуатации

Результаты поиска

Содержание Goodrive20-EU VFD Series

Отзывы:

Похожие инструкции для Goodrive20-EU VFD Series

Бренды по названию

Популярные бренды