INVT Goodrive20-EU VFD Series Скачать руководство пользователя страница 109

Страница: 109 / 173

Goodrive20-EU Series VFD

Fault tracking

-104-

Item to be checked

Details

Check mode

Criterion

Ventilating duct

Ensure whether there is

stuff or foreign objection

in the cooling fan, air

vent.

Visual examination NA

6.1.2 Cooling fan

The VFD's cooling fan has a minimum life span of 25,000 operating hours. The actual life span
depends on the VFD usage and ambient temperature.

The operating hours can be found through P07.14 (accumulative hours of the VFD).

Fan failure can be predicted by the increasing noise from the fan bearings. If the VFD is

operated in a critical part of a process, fan replacement is recommended once these
symptoms appear. Replacement fans are available from INVT.



Read and follow the instructions in Chapter 1 "Safety precautions".

Ignoring the instructions would cause physical injury or death, or damage

to the equipment.

1. Stop the VFD and disconnect it from the AC power source and wait for at least the time

designated on the VFD.

2. Lever the fan holder off the drive frame with a screwdriver and lift the hinged fan holder

slightly upward from its front edge.

3. Disconnect the fan cable. Remove the installation bracket.

4. Install the bracket to the reversed direction. Pay attention the air direction of the VFD and

the fan as the figure below:

Rotation
direction

Air direction

Figure 6-1 Fan installation of the VFDs 1PH, 230V,

≤2.2kW

Содержание Goodrive20-EU VFD Series














































































































































































Результаты поиска

Содержание Goodrive20-EU VFD Series

Отзывы:

Похожие инструкции для Goodrive20-EU VFD Series

Бренды по названию

Популярные бренды

INVT Goodrive20-EU VFD Series, Руководство по эксплуатации

Результаты поиска

Содержание Goodrive20-EU VFD Series

Отзывы:

Похожие инструкции для Goodrive20-EU VFD Series

Бренды по названию

Популярные бренды