INVT Goodrive20-EU VFD Series Скачать руководство пользователя страница 106

Страница: 106 / 173

Goodrive20-EU Series VFD

Fault tracking

-101-

Chapter 6 Fault tracking

6.1 Fault prevention

This chapter describes how to carry out preventive maintenance on VFDs.

6.1.1 Periodical maintenance

If the VFD is installed in an environment that meets requirements, little maintenance is needed.

The following table describes the routine maintenance periods recommended by INVT. For
more detailed information on maintenance, please contact us.

Item to be checked

Details

Check mode

Criterion

Ambient environment

Check the ambient

temperature, humidity

and vibration and

ensure there is no dust,

gas, oil fog and water

drop.

Visual examination

and instrument

test

Conforming to the

manual.

Ensure there are no

tools or other foreign or

dangerous objects

Visual examination

There are no tools

or dangerous

objects.

Voltage

Ensure the main circuit

and control circuit are

normal.

Measurement by

multimeter

Conforming to the

manual.

Keypad

Ensure the display is

clear enough

Visual examination

The characters

are displayed

normally.

Ensure the characters

are displayed totally

Visual examination

Conforming to the

manual.

Main

circuit

For public use

Ensure the screws are

tightened scurrility

Tighten up

Ensure there is no

distortion, crackles,

damage or

color-changing caused

by overheating and

aging to the machine

and insulator.

Visual examination NA

Содержание Goodrive20-EU VFD Series














































































































































































Результаты поиска

Содержание Goodrive20-EU VFD Series

Отзывы:

Похожие инструкции для Goodrive20-EU VFD Series

Бренды по названию

Популярные бренды

INVT Goodrive20-EU VFD Series, Руководство по эксплуатации

Результаты поиска

Содержание Goodrive20-EU VFD Series

Отзывы:

Похожие инструкции для Goodrive20-EU VFD Series

Бренды по названию

Популярные бренды