INVT Goodrive20-EU VFD Series Скачать руководство пользователя страница 168

Страница: 168 / 173

Goodrive20-EU Series VFD

Optional peripheral accessories

-163-

Model

Type of

braking

unit

Braking

resistor at

100% of

braking

torque (Ω)

Consumed power of the braking

resistor (kW)

Min.

braking

resistor

(Ω)

10%

braking

50%

braking

80%

braking

GD20-1R5G-4-EU

326

0.23

1.13

1.80

170

GD20-2R2G-4-EU

222

0.33

1.65

2.64

130

GD20-004G-4-EU

122

0.6

4.8

GD20-5R5G-4-EU

89.1

0.75

4.13

6.6

GD20-7R5G-4-EU

65.3

1.13

5.63

GD20-011G-4-EU

44.5

1.65

8.25

13.2

GD20-015G-4-EU

32.0

2.25

11.3

GD20-018G-4-EU

GD20-022G-4-EU

GD20-030G-4-EU

GD20-037G-4-EU

11.7

GD20-045G-4-B-EU

GD20-055G-4-B-EU

GD20-075G-4-B-EU

6.5

6.4

GD20-090G-4-B-EU

5.4

108

4.4

GD20-110G-4-B-EU

4.5

132

4.4

Note:



Select the resistor and power of the braking unit according to the data our company

provided.



The braking resistor may increase the braking torque of the VFD. The resistor power in the

above table is designed on 100% braking torque and 10% braking usage ratio. If the users

need more braking torque, the braking resistor can decrease properly and the power needs
to be magnified.



Never use a braking resistor with a resistance below the minimum value

specified for the particular drive. The drive and the internal chopper are

not able to handle the overcurrent caused by the low resistance.



Increase the power of the braking resistor properly in the frequent braking

situation (the frequency usage ratio is more than 10%).

C.7.2 Braking resistor installation

Braking resistor cables need to be shielded cables.

Install all resistors in a place where they will cool.

Содержание Goodrive20-EU VFD Series














































































































































































Результаты поиска

Содержание Goodrive20-EU VFD Series

Отзывы:

Похожие инструкции для Goodrive20-EU VFD Series

Бренды по названию

Популярные бренды

INVT Goodrive20-EU VFD Series, Руководство по эксплуатации

Результаты поиска

Содержание Goodrive20-EU VFD Series

Отзывы:

Похожие инструкции для Goodrive20-EU VFD Series

Бренды по названию

Популярные бренды