INVT Goodrive20-EU VFD Series Скачать руководство пользователя страница 102

Страница: 102 / 173

Goodrive20-EU Series VFD

Function parameters

-97-

Function

code

Name

Description

Default Modify

the system processing time, if the answer delay

is longer than the system processing time, then

after the system deal with the data, waits until

achieving the answer delay time to send the data

to the upper monitor.

P14.04

Communication

overtime fault

time

0.0 (invalid), 0.1

–60.0s

When the function code is set as 0.0, the

communication overtime parameter is invalid.

When the function code is set as non-zero, if the

interval time between two communications

exceeds the communication overtime, the

system will report "485 communication faults"

(CE).

0.0s

○

P14.05

Transmission

error

processing

0: Alarm and stop freely

1: No alarm and continue running

2: No alarm and stop as per the stop mode (only

under communication control mode)

3: No alarm and stop as per the stop mode

(under all control modes)

○

P14.06

Communication

processing

action selection

0x000

–0x111

Ones place: Responding to write operations

0: Yes

1: No

Tens place: Communication encryption

0: Disabled

1: Enabled

Hundreds place: User-defined communication

command address

0: Disabled

1: Enabled

0x000

○

P14.07

User-defined

address for

running

commands

0x0000

–0xffff

0x1000

○

P14.08

User-defined

address for

frequency

setting

0x0000

–0xffff

0x2000

○

Содержание Goodrive20-EU VFD Series














































































































































































Результаты поиска

Содержание Goodrive20-EU VFD Series

Отзывы:

Похожие инструкции для Goodrive20-EU VFD Series

Бренды по названию

Популярные бренды

INVT Goodrive20-EU VFD Series, Руководство по эксплуатации

Результаты поиска

Содержание Goodrive20-EU VFD Series

Отзывы:

Похожие инструкции для Goodrive20-EU VFD Series

Бренды по названию

Популярные бренды