INVT Goodrive20-EU VFD Series Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 173

background image

Goodrive20-EU Series VFD

Keypad operation

-31-

If the fault persists, the fault code is continuously displayed.

4.2.4 Editing function codes

You can press the PRG/ESC key to enter the editing mode in stopped, running, or fault alarm

state (if a user password is used, see the description of P07.00). The editing mode contains

two levels of menus in the following sequence: Function code group or function code number
→ Function code setting. You can press the DATA/ENT key to enter the function parameter
display interface. On the function parameter display interface, you can press the DATA/ENT

key to save parameter settings or press the PRG/ESC key to exit the parameter display

interface.

RUN/TUNE

FWD/REV LOCAL/REMOT

Hz

TRIP

A

V

RPM

%

RUN/TUNE

FWD/REV LOCAL/REMOT

TRIP

Hz

A

V

RUN/TUNE

FWD/REV LOCAL/REMOT

TRIP

Hz

A

V

RPM

%

RPM

%

Figure 4-3 Status display

4.3 Operations on the keypad

You can operate the VFD by using the keypad. For details about function code descriptions,
see the function code list.

4.3.1 Modifying VFD function codes

The VFD provides three levels of menus, including:

1. Function code group number (level-1 menu)

2. Function code number (level-2 menu)

3. Function code setting (level-3 menu)

Note:

When performing operations on the level-3 menu, you can press the PRG/ESC or

DATA/ENT key to return to the level-2 menu. If you press the DATA/ENT key, the set value of

the parameter is saved to the control board first, and then the level-2 menu is returned,

displaying the next function code. If you press the PRG/ESC key, the level-2 menu is returned

directly, without saving the set value of the parameter, and the current function code is
displayed.

If you enter the level-3 menu but the parameter does not have a digit blinking, the parameter
cannot be modified due to either of the following reasons:

1) It is read only. Read-only parameters include actual detection parameters and running
record parameters.

2) It cannot be modified in running state and can be modified only in stopped state.

«
...
34
35
36
37
38
...
»

Содержание Goodrive20-EU VFD Series














































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Goodrive20-EU VFD Series

MINAS A5 Series

Бренд: Panasonic Страницы: 19

Бренд: CENTENT Страницы: 48

Бренд: Toshiba Страницы: 6

H802A - SD - Disk Drive

Бренд: Toshiba Страницы: 1

Бренд: Toshiba Страницы: 12

Бренд: Toshiba Страницы: 12

Бренд: Toshiba Страницы: 16

Бренд: Toshiba Страницы: 12

Бренд: Toshiba Страницы: 12

Бренд: Toshiba Страницы: 12

Бренд: Toshiba Страницы: 16

C2402 - SD - DVD-ROM Drive

Бренд: Toshiba Страницы: 12

Бренд: Toshiba Страницы: 14

Бренд: Toshiba Страницы: 29

SD-M1212 - DVD-ROM Drive - IDE

Бренд: Toshiba Страницы: 35

R6472 - DVD±RW Drive - IDE

Бренд: Toshiba Страницы: 35

PA3454U-1DV2 - External USB 2.0 DVD Super Multi Drive

Бренд: Toshiba Страницы: 65

Бренд: Yamaha Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды