479
Continued on next page
Appendix/External Devices/Troubleshootin
g
If
A
n
y
E
rror
M
e
ss
ag
e A
p
p
ear
s
If Any Error Message Appears
d
Numbers enclosed in parentheses contained in i-mode error messages are codes used to distinguish
errors sent from the i-mode center.
Error Message
Explanation and Solution
Refer to
“Invalid UIM Auto start not
possible”
d
This message appears when you attempt to automatically launch
i-
α
ppli restricted by the FOMA card operational restriction function.
p.38
“Invalid UIM Requested service
not available”
d
This message appears when you select a desktop icon for data
protected by the FOMA card operational restriction function.
d
This message appears when you select a screen memo, MessageR
or MessageF protected by the FOMA card operational restriction
function.
p.38
“Invalid UIM Requested software
failed to start”
d
This message appears when you attempt to select and launch i-
α
ppli
restricted by the FOMA card operational restriction function.
p.38
“Reading UIM Cannot start”
d
This message appears when you attempt to perform an operation
related to the FOMA card (UIM) while the FOMA card (UIM) is being
read. Retry later.
−
“Insert UIM”
d
This message appears when the FOMA card (UIM) is not correctly
inserted or may be damaged. Make sure that the FOMA card (UIM)
is correctly inserted.
p.37
“Data in IC card is full Replace?”
d
This message appears when you attempt to download Osaifu-Keitai
i-
α
ppli but the space is not enough on the IC card. Select “YES” to
display already registered Osaifu-Keitai services and the space
(bytes) on the IC card. Check the size required, select services to
remove, and launch i-
α
ppli to remove them.
−
““i-
α
ppli To” function is not set”
d
When you attempt to launch software from a site, message, the
infrared data exchange function, the Bar code reader or the IC card,
it does not launch because the specified software is not permitted to
be linked.
p.299
“Data transmission is frequent
Continue transmission?”
d
This message appears when the number of communications that are
using i-
α
ppli and have been established in a given time is extremely
large. Select “YES” to continue to make i-
α
ppli communication, or
“NO” to quit the communication. To quit using an i-
α
ppli program,
select “Terminate i-
α
ppli”.
−
“Continue using i-
α
ppli and
transmit data?”
d
This message appears when you select “NO” or “Terminate i-
α
ppli”
in response to the message “Data transmission is frequent Continue
transmission?”. Select “YES” to continue i-
α
ppli communication. To
quit using an i-
α
ppli program, select “Terminate i-
α
ppli”.
−
“Check new messages is set all
OFF”
d
New messages cannot be checked because none of the items is
selected in “Set check new messages”.
Select items to check in “Set check new messages”.
p.278
“Insert miniSD”
d
This message appears when the miniSD memory card is not
inserted correctly or may be damaged. Check that the miniSD
memory card is properly inserted into the FOMA terminal.
p.354
“Replace with a new one or check
the disk”
d
Check the miniSD memory card.
p.358
“PIN1 code blocked”
d
This message appears when the power is turned on during PIN1
code lock. Press
d
to display the PUK code entry screen, then
enter the PUK code correctly to release the lock.
p.158
“PUK blocked”
d
This message appears when you attempt to power on or perform
operations related to the FOMA card (UIM) when the PUK code is
blocked. Contact the DoCoMo service counter.
p.157
“SSL session cannot be
established”
d
This message appears when a connection to an SSL site or website
was not established. Retry connection.
−
“SSL session failed”
d
This message appears when an SSL communication is interrupted
due to an error occurring during authentication for an SSL
connection.
−