EXFO Power Blazer 88000 Series Скачать руководство пользователя

Страница: 524 / 803

Test Results

512

88000 Series

Summary (S-OAM and MPLS-TP OAM)



RX Line Utilization

meter and value, available with

Loopback

function, indicate the line rate utilization percentage (only LBR frames
are considered) received in the last second.



TST RX

Rate

meter and value, available with

Test

function, indicate the

quantity of TST frames received in the last second.



Frame Delay

meter and value, available with

Frame Delay

function,

indicate the average of the measured frame delays in the last second.



Frame Loss Ratio

meter, available with

Frame Loss

function,

indicates for both Near-End and Far-End the last measured frame loss
ratio in the last second.



Synthetic Loss Ratio

meter, available with

Synthetic Loss

function

which is available with Ethernet OAM, indicates for both Near-End and
Far-End the last measured Synthetic Loss ratio in the last second.

Note:

Refer to

S-OAM and MPLS-TP OAM

on page 452 for more

alarms/errors/statistics information.

Summary

Refer to

S-OAM and MPLS-TP OAM

on page 452 for more information on

alarms.

Thresholds

Refer to

Thresholds

on page 269 for more information.

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды

EXFO Power Blazer 88000 Series, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды