EXFO Power Blazer 88000 Series Скачать руководство пользователя

Страница: 336 / 803

Test Setup - Test Configurator, Timer, and System

324

88000 Series

SyncE



Pass/Fail Verdict

check box when selected (default) enables the use

of the pass/fail verdict. The global pass/fail verdict is based on the
following criteria:

ESMC Rate Threshold

(when enabled),

Mismatch Monitoring

(when enabled),

ESMC Loss

, or

Link Down



ESMC Rate Threshold

check box when selected (default) enables the

ESMC rate threshold monitoring which will declare a Fail verdict when
the ESMC frame rate is outside the range of 0.8 to 10.2 frames/s.

ESMC Generation



Generated QL

The

Generated QL

check box when selected (default) enables the

generation of the selected QL message.

The

Generated QL

field allows the selection of the QL message that

will be generated. See page 450 for the list of QL message (default is

QL-EEC2/ST3

Note:

For 1GE Electrical interface using

Local Clock

set to

Slave

, the

Generated

is not configurable and is set to

QL-DNU/DUS

with its check box

selected.



QL Rate (frame/s)

defines the frame rate at which the ESMC transmit

the QL message value:

(default),

, or

frames per second. For 1GE

Electrical interface using

Local Clock

set to

Slave

, the

QL Rate

is not

configurable and is set to

frame/s.

Restore SyncE Defaults

Reverts the SyncE test application to its default factory settings.

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды

EXFO Power Blazer 88000 Series, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды