EXFO Power Blazer 88000 Series Скачать руководство пользователя | Manualshive

Страница: 276 / 803

background image

Test Setup - Test Configurator, Timer, and System

264

88000 Series

RFC 6349

RFC 6349

From the

Test

menu, tap

Setup

,

Test Configurator

, and the RFC 6349

block.

Connection



Operation Mode

allows the selection of the test operation mode:

Dual

Test Set

(

DTS

) or

EXFO|Worx Interop

.

The connection is graphically displayed with its status as follows:

Operation

Mode

Status

Description

Dual Test Set Disconnected

No connection established with a remote module.

NAT
LAN/WAN

,

WAN IP

Connection established with a remote module.
NAT LAN/WAN and WAN IP indicate presence of NAT
(Network Address Translation) router. The NAT router is
automatically detected and graphically displayed with
LAN/WAN indication as well as the WAN IP address
when the Power Blazer is behind a NAT router.
When there is a NAT at the Remote site, it is required to
create the following rules on this NAT router:
1- for UDP/TCP port 62819 to allow DTS
communication.
2- for the defined TCP port (see TCP Port on page 265).

EXFO|Worx
Interop

Disconnected

Verifier not detected (not reachable, invalid IP, or invalid
TCP port).

Ready or
Running

Verifier detected, either running (remote unit locked) or
ready to perform a test.
The detection of NAT (Network Address Translation)
router presence is automatically detected and
graphically displayed. The WAN IP address is also
displayed when the module is behind a NAT router.

Busy

Verifier busy with another client (locked).

«
...
274
275
276
277
278
...
»

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88000 Series

Бренд: Haier Страницы: 58

Бренд: EA Страницы: 24

Бренд: TCS Basys Controls Страницы: 2

medialon Showmaster Go

Бренд: 7th Sense Страницы: 2

Бренд: Olsberg Страницы: 68

Бренд: Water Specialist Страницы: 60

Бренд: Daspi Страницы: 16

Бренд: Daikin Страницы: 16

SmartMonitor MMU2-16LE Series

Бренд: EDI Страницы: 62

Бренд: Navilock Страницы: 14

ISC.ANT.U500/270DM-E

Бренд: Feig Electronic Страницы: 117

Bilge Pump Control Panel

Бренд: SPXFLOW Страницы: 14

SCENE MASTER - V1.0

Бренд: JBSYSTEMS Light Страницы: 24

Бренд: CALEFFI Страницы: 14

Бренд: ATEN Страницы: 176

AUTOMATIONWORX IBS PCI SC/I-T

Бренд: Phoenix Contact Страницы: 80

5400 Pilot Operated

Бренд: Valve Concepts Страницы: 18

SITEMANAGER 1115

Бренд: B&R Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды