EXFO Power Blazer 88000 Series Скачать руководство пользователя | Manualshive

Страница: 499 / 803

background image

Test Results

Power Blazer

487

Summary (EtherSAM)

Committed



Frame Loss Rate

indicates the rate of frames that are lost. The

reported value is the maximum rate of Frame Loss from all burst
sequences and ramp steps excluding the

CIR+EIR

,

EBS

, and

Traffic Policing

steps. Frame Loss is displayed as a percentage

value when the remote module does not support exponential
notation.



Max. Jitter (ms)

indicates the maximum measured delay

variation.



Max Latency (ms)

indicates the maximum measured round-trip

latency (delay). For Dual Test Set the local to remote and remote to
local values are reported for One-Way Latency Measurement Mode
while a single round-trip value is reported for Round-Trip Latency
Measurement Mode (see

Global Options



Avg RX Rate

, for

Service Performance Test

, indicates the

measured average utilization throughput.

Excess

Max RX Rate

, for

Service Configuration Test

, indicates the

measured maximum utilization throughput.



VLAN Preservation

indicates if any VLAN mismatch occurred during

any step of a Ramp or Burst tests as follows:

Grey: Undefined
Green: No Mismatch detected
Red: Mismatch detected

«
...
497
498
499
500
501
...
»

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88000 Series

Бренд: Paratec Страницы: 8

Бренд: J+J Страницы: 33

Бренд: Dantherm Страницы: 96

Бренд: Gascat Страницы: 32

Бренд: tams elektronik Страницы: 12

Бренд: Radware Страницы: 98

Бренд: RabbitCore Страницы: 34

Бренд: IDTECK Страницы: 12

Бренд: Banner Страницы: 2

CGLine+ Web Controller

Бренд: Eaton Страницы: 28

Бренд: DigiPower Страницы: 27

Бренд: Savant Страницы: 2

Бренд: Nordelettronica Страницы: 8

Бренд: ECKELMANN Страницы: 147

Бренд: National Instruments Страницы: 4

Бренд: National Instruments Страницы: 26

Бренд: Ebyte Страницы: 20

EG-PWC-PSWRC-01

Бренд: Energenie Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды