EXFO Power Blazer 88000 Series Скачать руководство пользователя | Manualshive

Страница: 314 / 803

background image

Test Setup - Test Configurator, Timer, and System

302

88000 Series

Signal - Signal Configuration (OTN)

Signal - Signal Configuration (OTN)

Note:

The following signal configuration parameters are available from the
interface block.

From the

Test

menu, tap

Setup

,

Test Configurator

, the interface block,

and on the

Signal

tab.



OTU4

,

OTU3

,

OTU3e1

,

OTU3e2

,

OTU2

,

OTU2f

,

OTU1f

,

OTU2e

,

OTU1e

, or

OTU1

Note:

At least one of the two check boxes,

FEC

or

Scrambler

, must be selected in

order to prevent potential alarms caused by a lack of bit transition on the
optical signal. For example to disable

FEC

, first select the

Scrambler

check

box then clear the

FEC

check box.



FEC

check box, when selected (default), enables the FEC in TX/RX

and allows detecting, reporting, and correcting up to 8 symbol
errors (Correctable) per codeword. If there are over 8 symbol
errors detected, they are reported as uncorrectable errors.



Scrambler

check box, when selected (default), provides enough

“0” and “1” transitions on the optical signal for clock recovery.

Note:

When the

Scrambler

check box is cleared, the receiver circuitry is forced to

operate in a condition which is outside of the specified OTN operating
conditions, potentially causing alarms/errors. This configuration can be
used for special analysis in a lab environment.

«
...
312
313
314
315
316
...
»

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88000 Series

Бренд: Eaton Страницы: 166

Бренд: CAME Страницы: 32

Бренд: Jabra Страницы: 8

Бренд: Kathrein Страницы: 16

Бренд: S&P Страницы: 12

Бренд: S&C Страницы: 34

Бренд: S&C Страницы: 32

IntelliCap Plus

Бренд: S&C Страницы: 32

Бренд: S&P Страницы: 12

Бренд: S&C Страницы: 35

PetroVend PV200

Бренд: OPW Страницы: 2

Бренд: WAC Страницы: 5

GECO LUX GECO60

Бренд: GiBiDi Страницы: 48

Бренд: XtendLan Страницы: 12

Бренд: ZBA Страницы: 27

Бренд: M-system Страницы: 10

Бренд: Paser Страницы: 2

Бренд: Water Specialist Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды