EXFO Power Blazer 88000 Series Скачать руководство пользователя | Manualshive

Страница: 216 / 803

background image

Test Setup - Test Configurator, Timer, and System

204

88000 Series

MAC/IP/UDP

MAC/IP/UDP

Note:

Only available with Framed Layer 2 (see

Framing

).

From the

Test

menu, tap

Setup

,

Test Configurator

, and...



For

RFC 2544

and

EtherBERT

, tap on the protocol block.



For

EtherSAM

, and

Traffic Gen & Mon

, tap on the protocol block, and

on the

MAC/IP/UDP

tab. For Traffic Gen & Mon all parameters are

configurable per stream. For EtherSAM all parameters are configured
per service.

Stream Selection (Traffic Gen & Mon)

The Traffic Gen & Mon test application supports the configuration of up to
16 different streams. Select the stream to be configured by either using the
left/right arrow or by tapping over the stream numbers area then tapping
on a specific stream number.

Service Selection (EtherSAM)

The EtherSAM test application supports the configuration of up to 10
different services. Select the service to be configured by either using the
left/right arrow or by tapping over the service numbers area then tapping
on a specific service number.

Couple with Interface

The

Frame Format

,

Network Layer

, and all

IP

and

VLAN

settings are

coupled with the interface (see

on page 220) when the

Couple

with Interface

check box is selected (default). The

Source

MAC Address

is always coupled. Not available when using

Provider Encapsulation

.

«
...
214
215
216
217
218
...
»

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88000 Series

Бренд: Samson Страницы: 78

Бренд: Rachio Страницы: 16

Бренд: Parker Страницы: 30

Бренд: VAT Страницы: 22

Бренд: Samson Страницы: 52

Бренд: Samson Страницы: 32

Бренд: Danfoss Страницы: 59

Бренд: QUAD Страницы: 17

Бренд: fadini Страницы: 16

Бренд: Fairchild Страницы: 2

Бренд: Fairford Страницы: 233

Бренд: Federal Signal Corporation Страницы: 79

Бренд: Federal Signal Corporation Страницы: 32

Бренд: YUGE Страницы: 69

Бренд: Quectel Страницы: 232

Бренд: Quectel Страницы: 9

Бренд: Quectel Страницы: 73

Бренд: Rain Bird Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды