EXFO Power Blazer 88000 Series Скачать руководство пользователя

Страница: 158 / 803

Test Setup - Test Configurator, Timer, and System

146

88000 Series

Cable Test



Power Class

, available when PoE is enabled, selects the power class of

the simulated powered device:

Pass/Fail Verdict



Pass/Fail Verdict

check box when selected (default) enables the cable

test pass/fail verdict and allows setting the threshold values.



Prop. Delay Threshold (ns)

is the maximum time for a pulse to

reach the far end:

1000

ns (default is

1000

ns for 10 Mbit/s,

556

ns for 100 Mbit/s, and

570

ns for 1 Gbit/s).



Delay Skew Threshold (ns)

is the maximum time between the

fastest and slowest pairs of a 1000 Base-T signal:

120

(default is

ns).



Length Threshold (m)

is the maximum acceptable cable length:

120

m (0 to 394 feet) (default is

100

m (328 ft)).



PoE Loaded Voltage Thresholds (V)

, available when the

PoE

check box is selected, allows the configuration of the acceptable
voltage range when a load is applied: minimum value is either

(default) for Class 0 to 3 or

42.5

(default) for Class 4; maximum

value is 57 (default). A Pass vedict is declared when the measured
voltage is within the defined range.

Restore Cable Test Defaults

Reverts the configured parameters to their default values.

Power Class

Power Device

Class 0 (13.0W)

- (default)

Type 1

Class 1 (3.8W)

Class 2 (6.5W)

Class 3 (13.0W)

Class 4 (25.5W)

Type

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды

EXFO Power Blazer 88000 Series, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды