EXFO Power Blazer 88000 Series Скачать руководство пользователя

Страница: 97 / 803

Selecting and Starting a Test

Power Blazer

Transport Test Applications

Transport Test Applications

To select, configure, and start a Transport test:
1.

From the test menu, tap

Setup

From the

Test Applications

tab, under

Transport

, tap a test icon.

From the

Test Configurator

tab configure the signal structure and its

parameters.

3a.

Tap the

Modify

Structure

button to set the basic structure of the

test such as the interface/rate, connector, etc. (refer to

Modify

Structure Button

on page 108).

3b.

For CFP/QSFP interface, check for the optical validation check
mark

indicating that the transceiver matches the configured

interface/rate (refer to

Physical Interface Port - Test Configurator

Overview

on page 100).

3c.

Tap the interface block to configure the signal parameters (refer
to page 95).

3d.

For an embedded signal, tap the protocol block to configure the
signal (refer to page 95).

Modify Structure

Protocol Block

Test Block

Clock Block

Interface Block

Physical

Interface Port

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды

EXFO Power Blazer 88000 Series, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды