EXFO Power Blazer 88000 Series Скачать руководство пользователя | Manualshive

Страница: 717 / 803

background image

Glossary

Power Blazer

705

CPRI

Functional Description

As mentioned earlier, CPRI remotely locates the RE from the REC. This
means that the RE must be controlled, managed and synchronized from
the REC in addition to transporting the User information (Voice and user
application data) and all that on the same digital link. As such, CPRI is
composed of 3 communication flows multiplexed into a single serial signal
transmitted in the same optical fiber as illustrated in the following figure.

An electrical link is also available from CPRI but it is typically used for base
station shelf interconnection. Since a state machine drives the link
parameters (rates, protocol, and C&M channel) alignment, a BTS (defined
as Master in the standard) and RRH (defined as Slave in the standard)
interfaces are defined where the Master initiates the negotiation procedure
necessary to achieve this alignment.



Synchronization: Provides precise frequency and frame timing
alignment from BTS to RRH to ensure accurate frequency and timing of
the RF signal transmission and reception on the Air Interface. In
essence, it provides the reference frequency for the RE.



Control & Management (C&M): Management of the link between the
REC and RE as well as control over radio functions such as alarms and
power.



User: Also known as IQ Data, represents the voice and data
information that is exchanged by end-User Equipment (UE)

«
...
715
716
717
718
719
...
»

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88000 Series

Бренд: FAAC Страницы: 14

Бренд: MacDon Страницы: 32

Бренд: K&K Страницы: 6

Бренд: K'Nex Education Страницы: 56

Бренд: Paser Страницы: 2

Бренд: Computer Automation Technology Страницы: 55

Бренд: RKC INSTRUMENT Страницы: 10

Бренд: XtendLan Страницы: 12

Бренд: ZBA Страницы: 27

Бренд: M-system Страницы: 10

Бренд: IR-Tec Страницы: 14

Бренд: Aqua Lung Страницы: 24

Бренд: FMS Страницы: 9

Бренд: SIEB & MEYER Страницы: 119

TITAN-TRACKSIDE-6

Бренд: RC System Страницы: 4

Бренд: SainSmart Страницы: 49

Бренд: Aeroflex Страницы: 85

Бренд: Glitch'd Gaming Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды