EXFO Power Blazer 88000 Series Скачать руководство пользователя | Manualshive

Страница: 619 / 803

background image

Test Functions

Power Blazer

607

Ping & Trace Route

Trace Route



Max Hop Count

: Enter the maximum network device the packet is

allowed to go through. Choices are

1

to

255

;

128

by default.



Timeout (ms)

: Enter the maximum time allowed between an ICMP

echo and response at each hop. Choices are

200 ms

to

10000 ms

;

4000 ms

by default.



Trace Route

button starts the trace route tool with the specified

settings.

Results

To succeed, a ping command shall be acknowledged by the network
device within a given delay (

Timeout

). Typically a ping command can fail

for the following reasons:



The IP address is unavailable or unknown.



The time allowed to perform the ping command is too short.



The remote device is not supporting ICMP messaging.

To succeed, a trace route command shall be acknowledged by the
network device within a given delay (Timeout). Typically a trace route
command can fail for the following reasons:



The IP address is unavailable or unknown.



The time allowed to perform the trace route command is too short.



The remote device is not supporting ICMP messaging.

The ping and trace route results are displayed with the following columns:



No.

: Indicates the attempt number.

«
...
617
618
619
620
621
...
»

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88000 Series

Бренд: Watts Страницы: 2

Бренд: Canon Страницы: 2

Бренд: 7bit Страницы: 2

Бренд: Jafar Страницы: 15

Бренд: Gardena Страницы: 18

VLT Micro Drive FC 51 Series

Бренд: Danfoss Страницы: 23

Бренд: ECKELMANN Страницы: 178

Бренд: Fancom Страницы: 31

Бренд: 3M Страницы: 90

Бренд: National Instruments Страницы: 29

Бренд: Laars Страницы: 28

Бренд: hager Страницы: 4

Бренд: Whale Страницы: 8

Бренд: Tascam Страницы: 8

Бренд: Tenpilot Страницы: 2

Бренд: Widex Страницы: 17

Бренд: Ublox Страницы: 58

Бренд: D+H Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды