EXFO Power Blazer 88000 Series Скачать руководство пользователя

Страница: 174 / 803

Test Setup - Test Configurator, Timer, and System

162

88000 Series

EtherBERT, FC BERT, BERT (CPRI/OBSAI), and Unframed BERT

Note:

The following frame parameters are only available for OTN BERT test
application with Ethernet client (EoOTN).



Source MAC Address

is the module default and unique Source Media

Access Control (MAC) address that is automatically given to the
stream. Tap the

Source MAC Address

field if the stream MAC address

has to be changed and enter the new MAC address.



Destination MAC Address

is the destination MAC address for the

stream. The default setting is the MAC address of the port. Tap the

Destination MAC Address

field if the stream MAC address has to be

changed and enter the new MAC address.



VLAN ID

check box, when selected (cleared by default), allows the

configuration of the following VLAN parameters. Selecting the VLAN
check box affects the

Frame Size

value.



VLAN ID

sets the VLAN ID. Choices are

through

4095

(default

). Refer to

VLAN ID and Priority

on page 758 for more

information.



Priority

sets the VLAN user priority. Choices are

(default) to

Refer to

VLAN ID and Priority

on page 758 for more information.



Type

indicates the supported VLAN Ethernet type which is

0x8100

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды

EXFO Power Blazer 88000 Series, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды