EXFO Power Blazer 88000 Series Скачать руководство пользователя

Страница: 338 / 803

Test Setup - Test Configurator, Timer, and System

326

88000 Series

TA-SFP28

TA-SFP28

Gives the transceiver adapter insertion counter and information on the
inserted transceiver module.

Note:

Only available with FTBx-88260 modules.

From the

Test

menu, tap

Setup

Test Configurator

, tap on the interface

block and on the transceiver adaptor (

TA-...

) tab.

Port



Transceiver Adaptor Insertion Counter

indicates the number of time

a transceiver adaptor module has been inserted into this FTBx-88260
module port over its limit of 1000 insertions.



Transceiver Adaptor Parameters

are as follows:



indicates the name of the TA module (

TA-...



Serial Number

indicates the serial number of the TA module.



Revision

indicates the hardware revision of the TA module.



Battery

indicates the status level of the battery:

Good

Low

, or

Depleted



Optical Module Insertion Counter

indicates the number of time

an optical transceiver has been inserted into this transceiver
adaptor module port over its limit of 250 insertions.

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды

EXFO Power Blazer 88000 Series, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды