EXFO Power Blazer 88000 Series Скачать руководство пользователя | Manualshive

Страница: 228 / 803

background image

Test Setup - Test Configurator, Timer, and System

216

88000 Series

MAC/IP/UDP

The following configuration parameters are available for both

IPv4

and

IPv6

unless otherwise specified.



Quick Ping

button automatically starts the quick Ping utility for the

stream destination IP address and provides either a successful or failed
result. The quick Ping uses 3 attempts, a Delay of 1 second, a Timeout
of 2 seconds, and a Data Size of 32 Bytes. Refer to

Ping & Trace Route

on page 605 for more options.



Resolve MAC Address

check box, when selected (default), sends a

request to the network to retrieve the MAC address corresponding to
the selected destination IP address. This setting is coupled with the
Resolve MAC Address check box from

on page 210. The Resolve

MAC address status is displayed. Possible status are:



Source IP Multiplicator

check box, when selected (cleared by

default), allows changing the 7 LSB (Least Significant bit) of the source
IP address as specified in the range:

1-128

(default) or

0-127

.



Subnet Mask

(IPv4) allows entering the Subnet Mask for the stream.

The default setting is

255.255.0.0

. Not available when the

Automatic IP

(DHCP)

check box is selected.



Default Gateway

(IPv4) check box, when selected (cleared by

default), allows entering a default Gateway IP address. When the

Default Gateway

check box is selected, its default address is

0.0.0.0

.

The

Default Gateway

address is not configurable when the

Automatic

IP (DHCP)

check box is selected.

Status

Description

--

The

Resolve MAC address

is not enabled.

Resolving

The MAC address is being resolved.

Resolved

The MAC address is resolved.

Failed

The MAC address cannot be resolved.

«
...
226
227
228
229
230
...
»

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88000 Series

Бренд: Purmo Страницы: 2

Бренд: salmson Страницы: 78

Бренд: D+H Страницы: 16

Бренд: Quickie Страницы: 64

Бренд: Kamstrup Страницы: 7

Бренд: Grundfos Страницы: 16

Бренд: Loewe Страницы: 62

Бренд: Shimaden Страницы: 32

Бренд: Znshine Solar Страницы: 16

Phase Matrix PXI-1420

Бренд: National Instruments Страницы: 38

Бренд: WAGO Страницы: 134

Бренд: GAC Страницы: 9

Бренд: ALLEN & HEATH Страницы: 15

Бренд: Sames Страницы: 84

UNDER CONTROL CP-28

Бренд: G-Force Страницы: 2

Бренд: GBS Elettronica Страницы: 32

SYNCHRO QUASAR AC

Бренд: UCS Страницы: 10

MultiMode 1214-8

Бренд: Curtis Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды