EXFO Power Blazer 88000 Series Скачать руководство пользователя | Manualshive

Страница: 222 / 803

background image

Test Setup - Test Configurator, Timer, and System

210

88000 Series

MAC/IP/UDP

MAC



Source MAC Address

indicates the default and unique Media Access

Control (MAC) address given to the Ethernet port; editable when using

Provider Encapsulation

.



Destination MAC Address

: Enter the destination MAC address for the

stream. The default setting is the source MAC address. The destination
MAC Address field is not accessible when the

Resolve MAC Address

check box is selected.



Resolve MAC Address

check box, when selected (default), sends a

request to the network to retrieve the MAC address corresponding to
the selected destination IP address. This setting is coupled with the

Resolve MAC Address

check box from

on page 213. This check box

is not available when the

Network Layer

is set to

None

(refer to

Frame Structure



OAM Quick Ping

button automatically starts the quick Ping utility for

the stream destination MAC address and provides either a successful
or failed result. The quick Ping uses 3 attempts, a delay of 1 second,
and a Timeout of 5 seconds.



EtherType

is set to the following values by default and is configurable

from

0x0000

to

0xFFFF

when the

Network Layer

is set to

None

:

0x0000

when

Network Layer

is set to

None

0x0800

for IPv4

0x86DD

for IPv6

0x8847

for MPLS

0x88B7

when

Network Layer

is set to

None

with EtherBERT test.

0x8902

for S-OAM (available with EtherSAM)



OUI

, available when the frame format

802.3 SNAP

is selected, allows

the selection of the Organizationally Unique Identifier (OUI):

RFC1042

(0x000000) - (default)

User Defined

, available when

Network Layer

is set to

None

, allows

entering the

OUI

value:

0x000000

(default) to

0xFFFFFF

.

«
...
220
221
222
223
224
...
»

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88000 Series

Бренд: Warren Controls Страницы: 16

Бренд: GBD Страницы: 68

Бренд: Coris Страницы: 4

MS6-SV-...-D-10V24

Бренд: Festool Страницы: 32

Бренд: SOMFY Страницы: 56

Бренд: Hattersley Страницы: 2

Бренд: National Instruments Страницы: 6

Бренд: Bettis Страницы: 18

Бренд: EisSound Страницы: 10

Бренд: Elfa Страницы: 22

Бренд: Tripp Lite Страницы: 40

Бренд: Victaulic Страницы: 2

Бренд: Chamberlain Страницы: 4

Бренд: Shimaden Страницы: 16

GYRO TECH Nabco Multi-Module

Бренд: Nabco Страницы: 21

Бренд: Rauch Страницы: 85

EZ Power Remote

Бренд: Pogo Страницы: 1

Бренд: Simex Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды